Vehicles
12 not categorized PORSCHE 944 WHEEL BEARING KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.SACHS997STG1 Sachs stage 1 sport clutch kit Porsche 997 Carrera 05+ General Fitment911 2005-08
$3,202.40
Make a selection VR997TT900 With the success of our vr825 kit achieving a 206.2mph at the texas mile event in march 2010, we thought we had squeezed the most we could out of the 997 turbo. But we were wrong. This is where we introduce our vr900. Built and based off all the principles and products of our other kit, the vr900 goes 1 step further with larger injectors and a special custom tune from us. Having proved its power capabilities in cars all over the world, we reflash the ecu via the obdii port to make the 997 turbo a true monster. With increased fueling from 80lb injectors over the stock 57lb ones, we are able to run the 997 turbo to a new level. Our test vehicle was a 2009 997 turbo tiptronic and on 93octane at 1.5bar of boost, we...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09
$21,600.00
Make a selection 95111691100 Does your 924 tach needle climb in high gears and not move the car like it should? Does your 924 make a grinding noise in neutral? Does your 944 seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
From $264.50
Make a selection 96811691100 Does your Porsche's tach needle climb in high gears and not move the car like it should? Does your 968 make a grinding noise in neutral? Does it seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
From $827.84
Make a selection 96411691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our part # FVD116999 we also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection FVD1169141 Aasco recommends this combination of zf sachs race engineering clutch disc with torsion springs and pressure plate for their lightweight flywheel. The disc with torsion springs functions as a vibration damper between engine and gearbox, which provides an effortless release in 1st gear. This kit is suited for daily use and offers a superior driving experience. This combination has superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and is able to transmit higher torque (440 ft/lbs. / 600 nm max.). It is an ideal kit for lightly modified street or light use track cars. Clutch kit includes: 1 qty. Clutch disc with torsion springs (zf sachs race engineering, g...(choose a part on the right to read more)
$2,252.18
Make a selection FVD116102 The discs rigid hub with organic friction material has superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and is able to transmit higher torque (370 ft/lbs. / 500 nm max.). It is an ideal kit for lightly modified street or light use track cars. Clutch kit is made in Germany and includes: 1 qty. Clutch disc (zf sachs race engineering, gmbh) 1 qty. Pressure plate (zf sachs race engineering, gmbh) 1 qty. Release bearing 1 qty. Spline lubricant 9 qty. Pressure plate screws kit weighs 13 lbs. (6 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our par...(choose a part on the right to read more) General Fitment911 GT3 2007-11911 GT3 2003-05 911 1994-98 911 1989-94
From $1,243.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |